Monday, February 6, 2012

How To Repair A Hole In The Wall

This article will show you just how to repair a hole in the wall in just three easy steps. Fixing a hole in the wall is a very easy repair to make that anyone can do. Once repaired there should be no evidence of damage to the wall. This article shall be split into 2 parts with the first part dealing with smaller holes and the second part dealing with larger holes. Each will have two different approaches in the way the repair needs to be made. Let's begin with smaller type holes.

Part 1 Smaller Holes
These holes will vary in size from a quarter size hole to 3 inches in height and width. Metal patches will be used to fix these holes.

Repair A Hole In The Wall - Step 1 Clean Edges
This step is very simple for all that is needed is to make sure that all loose drywall is removed and pull back any loose paper and tape. The reason for this is to make sure there are no air pockets that may cause problems down the road.

Repair A Hole In The Wall - Step 2 Apply Patch
Hereis where the size of the hole must be taken into account since there are various sized patches. The type of patch that should be used is a metal patch for stability. Usually they can be purchased with three different sizes in one package. If a particular size needs to be purchased separately then knowing the exact size of the hole is necessary. The patch should be slightly larger than the hole. To apply the patch over the hole place some spackle around the hole. Just a very thin smooth layer is needed and it should reach beyond what the entire patch size is, Once the thin layer is on the wall just peel the paper off of the back of the patch and place it over the hole. With a spackle knife press down and move across the patch for a nice smooth tight fit against the wall. Then just spread a thin smooth layer of spackle over the patch.

Repair A Hole In The Wall - Step 3 Finishing Coat
For a final finish just spread some spackle over top of the patch once everything has dried and hardened over night from step 2. This coat should be a thin coat making sure to cover over any part of the patch from showing. If done right just a light sanding with some fine sand paper is needed once it has dried. Then of course it will need to be painted. Painting may require that the entire wall be painted to make sure the paint matches up well.

Part 2 Larger Holes
These holes will vary in size from a 4 inches to any size. Rather than a patch drywall ( sheetrock ) will be used to fix these holes.

Repair A Hole In The Wall - Step 1 Cut Hole
In the case of larger holes the hole will need to be  cut larger so that a piece of drywall can be installed. The reason for this is the drywall needs to be nailed or screwed into the studs. For that reason when cutting the hole larger a straight edge and exact measurements will be needed. Using a key hole saw or razor cut across from the hole to the nearby studs on both sides. Then using a straight edge draw a line down the middle of the studs on both sides to size you need that is lager than the hole. Once you have drawn straight level edges and are in the middle of the studs on both sides then cut the hole with a keyhole saw and a razor for slicing down the middle of the studs.

Repair A Hole In The Wall - Step 2 Install Drywall
Now that you have a nice square or rectangular hole, in which the studs are available to screw or nail a piece of drywall into, the hole must be measured. With that measurement cut a piece of drywall that is the same thickness as the drywall on the wall. Place the drywall into the hole and nail or screw it to the studs on each side.

Repair A Hole In The Wall - Step 3 Tape and Spackle
Now all that is needed is some tape and spackle to seal the joints for a smooth look. Place a thin layer of spackle over all of the joints making sure it is smooth and thin with no air pockets or drywall showing. The spackle also needs to go beyond all the edges of the paper tape that need to go over top. Deal with one joint at a time. Once the tape has been placed on use the spackle knife real tight to the wall and scrape up all spackle for a smooth tight finish. Once all the joints have been completed place a thin layer of spackle over top of the tape. Very thin but smooth layer so there will be minimal sanding. Once this has dried over night a final skim coat over top will fill in the edges and any air pockets, or tape that may be showing. If done right very little sanding will be needed. Using a very fine grit sand paper make sure everything is smooth as can be. Once done and everything has dried painting can now take place.

This is how to repair all holes in walls so that any damage that once was is no more. Good luck!

3 comments:

Interior Painting said...

All the steps can be very useful for repair purpose. Interior Painting work must be done carefully to decorate the interior of your house after repairing the damaged parts of the interior.

Milliscent Morgan said...

Such a great honor to be here and allow me to leave my reaction, only thing I could say about this blog is so amazing same as with the blog of interior painting Miami. Thanks!

Talmage Dangerfield said...

My wife and I are going to paint our bedroom in a couple of days, but there is a big hole in the wall. I'm so glad that I found these tips on how to fix it. If I had realized how easy it was, I never would have put it off for this long. http://www.paintingtrends.com.au/services/

PQI Interior DIY RSS Feed

Most Recent Home Improvement - Associated Content